me20 20w single output external power medical series www.slpower.com me20 rev 2.7 2-may-16 1 features ? meets ul/en/iec60601-1-2, 4th ed. for emc * ? approved to en/iec/ul60601-1, 3rd edition with isolation levels which satisfy the 2 mopp requirements. ? meets doe efficiency level vi requirements ? no load input power ? average efficiency ? up to 20w of ac-dc power ? universal input 90-264vac input range ? desktop and wall-plug versions ? meets en55011/cispr11, fcc part 15.109 class b conducted & radiated emissions, with 6db margin ? e-cap life of >10 years ? >1,000,000 hours mtbf ? 3 year warranty ? ip22 rated enclosure description a high performance ac to dc external power supply family designed for medical applications. the me20a medical series low power external ac-dc power supplies are approved to safety en/iec/ul60601-1, 3rd edition with isolation levels which satisfy the 2 mopp requirements and designed to ul/en/iec60601-1-2, 4th edition for emc * . the me20a series models will operate at universal input range of 90 to 264vac over the wide temperature range of -20c to +50c, delivering full rated output power up to +40c and applicable output power derating at 50 c. these models are available in desktop and wall-plug versions; include an ip22 rating per iec60529 for the enclosure, and output cable terminated at a variety of output connectors. these models use only high quality electrolytic capacitors, providing greater than 10 years life operating at rated output conditions. * consult factory for table 9 compliance information. model selection model output output ripple & line load output input number volts current power noise 1 regulation regulation connector configuration me20a0503f01 5.0v 3.00a 15w 75mv pk-pk 1% 5% 2.5 x 5.5 x 9.5mm straight barrel type, center positive class i desktop, iec60320 c14 receptacle me20a0603f01 5.9v 2.50a 15w 75mv pk-pk 1% 5% me20a0703f01 7.5v 2.00a 15w 75mv pk-pk 1% 5% me20a0903f01 9.0v 2.00a 18w 90mv pk-pk 1% 5% me20a1203f01 12.0v 1.50a 18w 120mv pk-pk 1% 5% me20a1503f01 15.0v 1.20a 18w 150mv pk-pk 1% 5% me20a1803f01 18.0v 1.00a 18w 180mv pk-pk 1% 5% me20a2403f01 24.0v 0.83a 20w 240mv pk-pk 1% 5% me20a4803f01 48.0v 0.42a 20w 480mv pk-pk 1% 5% me20a0503n01 5.0v 3.00a 15w 75mv pk-pk 1% 5% 2.5 x 5.5 x 9.5mm straight barrel type, center positive class ii desktop, iec60320 c8 receptacle me20a0603n01 5.9v 2.50a 15w 75mv pk-pk 1% 5% me20a0703n01 7.5v 2.00a 15w 75mv pk-pk 1% 5% me20a0903n01 9.0v 2.00a 18w 90mv pk-pk 1% 5% me20a1203n01 12.0v 1.50a 18w 120mv pk-pk 1% 5% me20a1503n01 15.0v 1.20a 18w 150mv pk-pk 1% 5% me20a1803n01 18.0v 1.00a 18w 180mv pk-pk 1% 5% me20a2403n01 24.0v 0.83a 20w 240mv pk-pk 1% 5% me20a4803n01 48.0v 0.42a 20w 480mv pk-pk 1% 5% lps
me20 20w single output external power medical series www.slpower.com me20 rev 2.7 2-may-16 2 model selection (continued) model output output ripple & line load output input number volts current power noise 1 regulation regulation connector configuration me20a0503q01 5.0v 3.00a 15w 75mv pk-pk 1% 5% 2.5 x 5.5 x 9.5mm straight barrel type, center positive class ii desktop, iec60320 c18 receptacle me20a0603q01 5.9v 2.50a 15w 75mv pk-pk 1% 5% me20a0703q01 7.5v 2.00a 15w 75mv pk-pk 1% 5% me20a0903q01 9.0v 2.00a 18w 90mv pk-pk 1% 5% me20a1203q01 12.0v 1.50a 18w 120mv pk-pk 1% 5% me20a1503q01 15.0v 1.20a 18w 150mv pk-pk 1% 5% me20a1803q01 18.0v 1.00a 18w 180mv pk-pk 1% 5% me20a2403q01 24.0v 0.83a 20w 240mv pk-pk 1% 5% me20a4803q01 48.0v 0.42a 20w 480mv pk-pk 1% 5% me20a0503b01 5.0v 3.00a 15w 75mv pk-pk 1% 5% 2.5 x 5.5 x 9.5mm straight barrel type, center positive class ii wall-plug, interchangeable blades (north american blade included) 2 me20a0603b01 5.9v 2.50a 15w 75mv pk-pk 1% 5% me20a0703b01 7.5v 2.00a 15w 75mv pk-pk 1% 5% me20a0903b01 9.0v 2.00a 18w 90mv pk-pk 1% 5% me20a1203b01 12.0v 1.50a 18w 120mv pk-pk 1% 5% me20a1503b01 15.0v 1.20a 18w 150mv pk-pk 1% 5% me20a1803b01 18.0v 1.00a 18w 180mv pk-pk 1% 5% me20a2403b01 24.0v 0.83a 20w 240mv pk-pk 1% 5% me20a4803b01 48.0v 0.42a 20w 480mv pk-pk 1% 5% me20a0503c01 5.0v 3.00a 15w 75mv pk-pk 1% 5% 2.5 x 5.5 x 9.5mm straight barrel type, center positive class ii wall-plug, fixed north american blades3 me20a0603c01 5.9v 2.50a 15w 75mv pk-pk 1% 5% me20a0703c01 7.5v 2.00a 15w 75mv pk-pk 1% 5% me20a0903c01 9.0v 2.00a 18w 90mv pk-pk 1% 5% me20a1203c01 12.0v 1.50a 18w 120mv pk-pk 1% 5% me20a1503c01 15.0v 1.20a 18w 150mv pk-pk 1% 5% me20a1803c01 18.0v 1.00a 18w 180mv pk-pk 1% 5% me20a2403c01 24.0v 0.83a 20w 240mv pk-pk 1% 5% ME20A4803C01 48.0v 0.42a 20w 480mv pk-pk 1% 5% notes: 1 . m e a s u r e d a t t h e o u t p u t c o n n e c t o r , w i t h n o i s e p r o b e d i r e c t l y a c r o s s o u t p u t a n d l o a d t e r m i n a t e d w i t h 0 . 1 f c e r a m i c a n d 1 0 f l o w e s r c a p a c i t o r s . f o r 5 v a n d 6 v m o d e l s , v a l u e s l i s t e d a r e t y p i c a l , 1 0 0 m v p k - p k m a x i m u m w i t h 0 . 1 f c e r a m i c a n d 4 7 f l o w e s r c a p a c i t o r s u s e d a t m e a s u r e m e n t p o i n t . 2. order blade kit kt-1027k for other blades (eu. uk, australia) 3. for eu fixed blades, replace ?c? in the model number with ?m?, for uk blades, replace ?c? with ?g?, for australia blades, replace ?c? with ?h?. 4. for input class i models: for ac gnd connected to output common (-), insert a ?b? in the part number where the ?a? is located (me20b0503f01). 5. all specifications are typical at nominal input, full load, at 25 c ambient unless noted. general specifications ac input 100-240vac, 10%, 47-63hz, 1 ? turn on time less than 700ms @115vac, full load input current 100vac: 0.5a, 240vac: 0.2a hold-up time 20ms min., at full load, 100vac input inrush current 264vac, cold start: will not exceed 40a overtemperature protection will shutdown upon an overtemperature condition, auto-recovery. input fuses f1, f2: 3.15a, 250vac fuses (line & neutral lines) provided on all models overload protection 130 to 180% of rating, hiccup mode earth leakage current i n p u t - g n d : < 5 0 0 a @ 2 6 4 v a c , 6 0 h z , n c output-gnd: <4ma@264vac, 60hz, nc short circuit protection hiccup mode, auto recovery. efficiency >87%, typical overvoltage protection 130 to 150% of output voltage, hiccup mode output power 15 to 20w continuous ? see models chart for specific voltage model ratings. isolation input-output: 2 mopp input-ground: 1 mopp output-ground: 1500vac no load input power <0.1w per doe efficiency level vi requirements safety standards ansi/aami es60601-1:2005/(r)2012, csa can/csa-c22.2 no, 60601-1:14; iec60601- 1:2005+corr.2:2007+am:2012; en 60601- 1:2006/a11:2011, en60601-1: 2006/a12:2014, en60601-1:2006/a1:2013, ripple and noise see models chart on pg 1. operating temperature -20c to +70c
me20 20w single output external power medical series www.slpower.com me20 rev 2.7 2-may-16 3 general specifications (continued) output voltage see models chart on pg 1. temperature derating see derating curve below. transient response 500 s response time for return to within 0.5% of final value for any 50% load step over the range of 5% to 100% of rated load, ? i/ ? t< 0.2a/ s. max. voltage deviation is +/-3.5%. storage temperature -40c to +85c regulation see models chart on pg 1. altitude operating: to 5000m. non-operating: -500 to 40,000 ft. drop test 1.4m from table top to wooden platform, 4 faces. relative humidity 5% to 95%, non-condensing vibration operating: 0.003g/hz, 1.5grms overall, 3 axes, 10 min/axis, 1-500hz. non-oper.: random waveform, 3 minutes per axis, 3 axes and sine waveform, vib. frequency/acceleration: 10-500hz/1g, sweep rate of 1 octave / minutes, vibration time of 10 sweeps / axes, 3 axes shock operating: half-sine, 20gpk, 10ms, 3 axes, 6 shocks total non-operating: half-sine waveform, impact acceleration of 100g, pulse duration of 6 ms, number of shocks: 3 for each of the three axis dimensions see outline drawings mtbf >1.000,000 hours, full load, 110 & 220vac input, 25 c amb., per telcordia 332 issue 6 (stress method). weight 150g e-cap life >7 year life based on calculations at 115vac/60hz & 230vac/50hz, ambient 25c at 24 hrs per day, 365 days/year, 6 power up cycles per day. all specifications are typical at nominal input, full load, at 25 c ambient unless noted. emi/emc compliance conducted emissions: en55011/cispr22 class b, fcc part 15.107, class b: 6db margin typ, at 115 and 230vac radiated emissions: en55022/cispr22 class b, fcc part 15.109, class b: 3db margin typ, at 115 and 230vac common mode noise: high frequency (100khz-20mhz): <40ma pk-pk electro-static discharge (esd) immunity on power ports: en55024/iec61000-4-2, level 4: +/- 8kv contact, +/- 15kv air, criteria a iec60601-1-2, 4 th edition, table 4 radiated rf em fields susceptibility en55022/en61000-4-3, 10v/m, 80mhz-2.7ghz, 80% am at 1khz iec60601-1-2, 4 th edition, table 4 electrical fast transients (eft) /bursts: en55024/iec61000-4-4, level 4, +/-4kv, 100khz rep rate, 40a, criteria a iec60601-1-2, 4 th edition, table 5 surges, line to line (diff mode) and line to gnd (cmn mode) en55024/iec61000-4-5, level 4, +/-2kv dm, +/-4kv cm, criteria a surpasses iec60601-1-2, 4 th edition requirements. conducted disturbances induced by rf fields en55022/iec61000-4-6, 3.6v/m ? level 4, 0.15 to 80mhz; and 12v/m) in ism and amateur radio bands between 0.15mhz and 80mhz, 80% am at 1khz iec60601-1-2, 4 th edition, table 5 rated power frequency magnetic fields en55024/iec1000-4-8, level 4: 30 a/m, 50/60 hz iec60601-1-2, 4th edition, table 4 voltage interruptions, dips, sags & surges en55024/iecen61000-4-11: --100% dip for 10 ms, at 0, 45, 90, 135, 180, 225, 270 and 315 degrees, 100% dip for 20ms, 0 deg., criteria a --100% dip for 5000ms (250/300 cycles), criteria b --60% dip for 100ms, criteria b --30% dip for 500ms, criteria a iec60601-1-2, 4th edition, table 5 harmonic current emissions en55011/en61000-3-2, class a flicker test en61000-3-3 all specifications are typical at nominal input, full load, at 25 c ambient unless noted. consult factory for information regarding testing for or usage under special environments.
me20 20w single output external power medical series www.slpower.com me20 rev 2.7 2-may-16 4 me20 series output power derating curve mechanical drawings iec60320 c14 receptacle, 2.5 x 5.5 x 9.5mm barrel connector interchangeable n.a. blade, 2.5 x 5.5 x 9.5mm barrel connector notes: 1. all dimensions in mm. 2. interchangeable blade models come with north american blade fitted. for other blades (eu, uk, aust.) order blade kit kt1027k. 3. the unit should not be covered or enclosed to protect against excessive case temperature rise. 0 5 10 15 20 25 -20 -10 0 10 20 30 40 50 60 70 w a t t s a m b i e n t t e m p e r a t u r e ? c 5v 12v-18v 24v 48v
me20 20w single output external power medical series www.slpower.com me20 rev 2.7 2-may-16 5 connector information standard models include a 2.5 x 5.5 x 9.5mm straight barrel type connector (ault #3), center positive. other standard options are listed below. the ?03? in the standard model number is replaced by the applicable digits below. for other options, consult the factory. many other connector types (usb, xlr, etc) are available, contact sl power for more information. data sheet ? 2016 sl power electronics corp. the information and specifications contained herein are believed to be correct at the time of publication. however, sl power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. specifications are subject to change without notice.
|
